Blechnerei Stiegele · Radgasse 7 · Aalen

The fold holds. The solder only seals.

Tinplate is thin steel with a coat of tin on it. We lock two edges together with a fold, roll a wire into the rim so it keeps its shape, and then draw soft solder through the joint to shut it against milk, rain and smoke.

Sixteen pieces on the shelf. Pails from €96. Re-tinning from €34.

Two tall metal cans standing side by side against a hedge

Two carrying cans waiting on the gate for their rims to be re-wired.

Three ways two edges are joined

Each piece we fold uses one of these, or two stacked. Not one of them is glue.

Lap seam

One edge folded once, laid over its neighbour and hammered flat. It carries a funnel, a lantern sleeve and anything that is never lifted full.

Grooved seam

Both edges folded into hooks, hooked into one another and closed with a groover. This is what holds fourteen litres of milk off the floor.

Sweated joint

Cleaned, fluxed, and warmed until the solder runs into the fold on its own. It shuts the seam. It is not what stops the seam opening.

Pick a joint and see it in section

The drawing slices through two sheets and looks at them end on. Move the dial: the fold redraws, the bead moves, and the three pieces underneath change with them.

What holds it
One fold over a plain edge, hammered down
Two hooks locked into one another, then flattened
The fold underneath. The solder is only the seal
What it is used on
Funnels, lantern sleeves, light sheet under 0.4 mm
Pail bodies, stove pipe, anything carried full
Bottoms into bodies, spouts, every wet seam
How it lets go
Peels open if the piece is twisted or dropped
Opens a hair if the groover was run too hard
Goes grey and brittle if the iron was not hot
Two sheets of 0.35 mm tinplate, drawn eighty times over
Wide funnel16 cm mouth€38
Bench lantern sleeve26 cm tall€52
Pouring can3 litres€72
Melkeimer14 litres€178
Giesskanne9 litres€149
Stove-pipe elbow120 mm bore€46
Melkeimer5 litres€96
Rahmkelle skimmer20 cm bowl€44
Pierced lantern21 cm tall€64

What is on the plates

Every piece we fold
A metal pail with a wire bail hanging from a hook in a gardenDairy

Melkeimer, 5 litres

€96

Tinned iron, wired rim, 24 cm across

A metal pail with a wooden grip on its bail, standing on a plank shelfDairy

Melkeimer, 9 litres

€132

Tinned iron, wired rim, 29 cm across

A metal watering can with a long spout leaning against a rough stone wallWater

Giesskanne, 9 litres

€149

Grooved body seam, brass rose, 62 cm long

A small metal lantern pierced with stars and dots, standing on a wooden ledgeLight

Pierced lantern, 21 cm

€64

Star piercing, candle pan, ring handle

Smoke rising from a capped metal chimney pipe against a pale skyStove

Stove-pipe elbow, 120 mm

€46

Grooved seam, black iron, turns 90 degrees

Two iron bars lying in a blue flame on a bench plateTools

Soldering iron, 500 g

€58

Copper bit, iron shank, ash handle

A bundle of metal bars seen end on in close-upTools

Bar solder, 1 kg

€42

Tin-lead 40/60, for stove and garden seams

A pair of metal snips standing upright on a steel benchTools

Bench snips, 250 mm

€54

Straight pattern, forged jaws, flat handles

A maker running a torch flame along small metal pieces on a bench block

Hiltrud at the bench

The iron goes into the flame, comes out, gets wiped on the sal ammoniac block and tinned bright. Then it has to carry its heat into the sheet, not just touch it. A joint made with a cool iron looks the same for a week and then crumbles like chalk.

Hiltrud Stiegele took the shop over from her uncle in 2009. Eberhard Maierhöfer does the stove pipe and the re-tinning tank. Between them they fold around nine hundred pieces a year. Two pairs of hands cannot do more than that and still do it well.

To the plates